Christopher

Gas package safety inspection and maintenance. Replaced filters and cleaned burner compartment with CO2 tank. Both pieces of equipment executed the sequence of operation in heating. Verified gas valve/inducer motor operation. Checked all capacitors. Excellent temperature heat rise. Proper draining of condensate and evaporator coils were relatively clean. Both systems are functioning according to manufacture specifications. Pre-booked summer maintenance.

Install detectors – paid via C. C.

Gas package safety inspection and maintenance. Equipment executed the sequence of operation in heating. Changed filters. Checked gas valve and inducer motor. ECM blower motor. Blower wheel: clean. Excellent temperature heat rise. System underwent a recent tuneup with new condenser fan motor, capacitor and hard start kit. System is functioning according to manufacture specifications.

Performed a heating maintenance on three systems. All three systems executed the sequence of operation and heating with no carbon monoxide detected. Checked static pressure, blower motor amp draw and temperature heat rise. Casita run capacitor measured below manufacturer specifications. Estimate sent for replacement.

Recall: Technician During maintenance on November 11, hot water pilot light was extinguished. Followed instructions and re-ignited pilot light. Set hot water thermostat to setting B per client request. Note: hot water heater is old and making popcorn noises during operation

Indoor unit safety inspection and maintenance. Equipment executed the sequence of operation in heating with no carbon monoxide detected in the home. Replace filters and cleared condensate drain. Courtesy garage mini split service. Indoor air quality: active. Tested condenser fan motor and found bearings to be in good shape. Checked blower motor amp draw and static pressure measurements. Pre-booked summer maintenance. System is functioning according to manufacture specifications.

Split heat pump safety inspection and maintenance. Air handler POV is installed in the attic – access master closet. Outdoor unit is installed in the backyard. Air filters are 20 x 25 and 14 x 14. Cleared condensate via Jones valve. Tested static pressure and blower motor amp draw. Cycled system in heating and switch over valve was successful in operation. Excellent temperature heat rise and refrigerant circuit diagnostic was good. Pre-booked summer maintenance. System is functioning according to manufacture specifications.

Heating/cooling system inspection: Client will be selling the home. Recommend installing a float safety switch to meet city code inspection – estimate sent via email. Equipment executed the sequence of operation in heating with an excellent temperature heat rise. No carbon monoxide was detected in the home. Measured running capacitor for blower, compressor motor and condenser fan motor. Checked and documented refrigerant temperature and pressure. Checked wiring for loose connections. Thermostat/disconnect box: good system is functioning according to manufacturer specifications in heating and cooling. Float safety switch installed and tested for quality-charged CC on file.

Indoor unit safety inspection and maintenance. Equipment executed the sequence of operation in heating with no carbon monoxide detected in the home. Check static pressure measurements, blower motor amp draw and temperature heat rise. High voltage current regulator measured 7.5 out of 10uf. Replaced component and installed for easy technician access. Replaced filters. Client renewed club membership. Paid via check. System is functioning according to manufacture specifications.

Recall: noise on call for cooling Diagnose issue as loose filter would make noise in return grill when blower turned on. Tighten tabs in return register to keep filter tight from making noise when the blower would turn on. Solved issue.

installed smoke/CO detectors Paid via C. C.

Indoor unit safety inspection and maintenance. Equipment executed the sequence of operation in heating with no carbon monoxide detected in the home. Checked static pressure, blower motor amp draw and temperature heat rise. Thermostat – gas valve – inducer motor: good. Replaced filters. System is functioning according to manufacturer specifications.

Indoor unit safety inspection and maintenance. Natural gas furnaces are installed in the garage – mechanical closet. Outdoor units are on the roof. Washed air filters and cleared condensate drain. Both pieces of equipment executed the sequence of operation in heating. ECM blower motors. Checked temperature heat rise, gas valve and inducer motor. Measured static pressure measurements and blower motor amp draw. Recommend installing carbon monoxide detectors – estimate sent via mail. Client renew club membership. Both systems are functioning according to manufacture specifications.

Gas package - maintenance and safety inspection/demand call: no heat Client stated that heating was not working. Diagnosis of system revealed 24V control wires were broken and slipping from wire nuts. Courtesy reconnected and repaired control circuitry. Completed heating maintenance: Equipment executed the sequence of operation in heating. Checked gas valve and inducer motor. Evaporative coil was clean. Checked dual run capacitors. System is now functioning properly after repairs and maintenance.

Indoor unit and gas package safety inspection and maintenance. Both pieces of equipment executed the sequence of operation in heating. Changed filter and cleared condensate drain. Checked capacitors, inducer motor and gas valve. Checked temperature heat split. Evaporator coil: clean. Both systems are functioning according to manufacture specifications.

Indoor unit safety inspection with maintenance – garage mini split service. Replaced filters. Equipment executed the sequence of operation in heating. Checked temperature heat split, blower motor capacitor and motor amp draw. Inducer motor/gas valve: good. System is functioning properly according to manufacture specifications.

Estimate sent

Indoor unit safety inspection and maintenance. Equipment executed the sequence of operation in heating with no carbon monoxide detected in the home. Cleared condensate drain with pipe brush and replace filter. Thermostat: good. Checked blower capacitor, blower amp draw and static pressure. System is functioning according to manufacture specifications.

Safety inspection and maintenance on two gas package units. Both pieces of equipment executed the sequence of operation in heating. Replaced filters and cleaned burner compartment with CO2. Dual run/starting capacitors: good. Thermostats: good. Checked temperature heat rise, gas valve and inducer. Both systems are functioning according to manufacture specifications. Recommend installing carbon monoxide detectors.

Heat pump package maintenance and safety inspection. Checked refrigerant circuit diagnostics and dual run capacitors. Checked thermostats and temperature split. System is functioning according to manufacturer specifications.

Indoor unit safety inspection and maintenance. Cycled system in heating and measured temperature heat rise. Checked static pressure measurements and blower motor amp draw (see notes and photos). Replaced filter. Helped client with thermostat function and operation. System is functioning according to manufacturer specifications.

Indoor unit safety inspection and maintenance. Two gas furnace upflow units, installed in the garage with filter racks. Heat pump installed at the casita. Casita air handler installed in a mechanical closet - outdoor unit installed in the courtyard. Main house outdoor units installed on the right side of the home. Gas furnaces executed the sequence of operation in heating with no carbon monoxide detected in the home. Gas valve/inducer motor: good. Verified proper blower motor amperage. Check temperature heat rise and static pressure measurements. Recommend replacing casita air filter. Cleared condensate drain lines. Installed compressor saver kit/starting capacitor on unit #0785. Somewhere down the line, recommend installing compressor saver kits on remaining systems to extend life of compressor motors. All systems are functioning according to manufacturer specifications.

Package unit safety inspection and maintenance. Equipment executed the sequence of operation in heating. Checked dual run capacitor and evaporative coil. Excellent temperature heat rise. Verified gas valve and inducer motor operation. Estimate sent for carbon monoxide detectors. System is functioning according to manufacturer specifications.

Demand call: no cool Client stated warm air was coming out of bedroom unit. Outdoor unit for bedroom was not powered. Opened electrical cabinet and found that contactor was engaged. 0 V found at the bottom of contactor. 0 V found at load voltage in disconnect box. 0 V found at line voltage in disconnect box. Opened service panel and found breaker was tripped. Clients stated that they have had frequent power surges. Recommend installing whole home surge protection and upgrading circuit breakers that control voltage for outdoor units. Both circuit breakers for outdoor units are rated for 30 A while both outdoor units are rated for 35/40 A. Clients paid for demand service via credit card.

Indoor unit safety inspection and maintenance. Horizontal gas furnaces installed in the attic. Access via hallway. Both pieces of equipment executed the sequence of operation in heating. Verified temperature heat rise, blower motor, inducer motor and gas valve function. Replace filters in the house and cleared condensate with PVC pipe brush. Found issue with zoned thermostat. Phone app and thermostat did not seem to be on the same page. Both systems are functioning according to manufacture specifications.