Coachella, CA

Installed 3 Ton American Standard Gold 17 Horizontal Split Heat Pump.

Performed a cool maintenance on a newly installed package unit. Check sequence of operation by checking out all electrical and also checked refrigeration levels by performing a temperature split. At this time was getting a 20° split and all electrical components are within range check blower motor, which is very clean. Also wash down package unit and finish maintenance by making sure your system went into heat mode correctly. All is within the range.

Provided estimate to replace 6 motion sensor.

On show called both numbers on file office called clients as well and no response. Waited 15 outside of house no response.

Performed annual safety check in cooling on a York package unit followed Sequence of operation Changed 20x25 filter location hallway checked amps on compressor and condenser fan motor capacitors temperature split working at range cleared condensation line rinsed condenser coil down unit is working to manufacture specification in cooling

Upon arrival system is on a running client stated there was a trip breaker and switch breaker on checked RLA on compressor are high max amps 14.7 system is running at 17 which is tripping breaker due to age of system. We will be installing 17 seer Monday the 28th. From 8 to 10.

Arrived to troubleshoot no power to part of the kitchen. During inspection of panel I discovered I tripped 2 pole breaker. After resetting breaker power was restored to kitchen. Additionally I inspected a motion sensor in closet that was not functioning correctly. After inspection of motion sensor I can confirm the sensor is malfunctioning. Customer would like an estimate to replace 5 motion sensors for 5 closets.

Performed an indoor maintenance and safety inspection. Gas furnace is located in an outdoor mechanical closet. Checked electric motors. Static pressure: N/A. Equipment executed the sequence of operation in heating. Temperature heat rise. Perform service on garage mini split. HVAC duct inspection. System is currently functioning according to manufacture specifications. Pre-booked heating maintenance.

Sent estimate for replacement for duck work there’s no access to replace we will need to cut drywall

After Diagnostic found faulty capacitor replaced capacitor unit is up and cooling performed temperature split and pressures system has Freon temperature split 15 degrees system is cooling but not properly unit is r 22 no longer manufactured sent estimates for replacement system is past life expectancy also signed up client on comfort plan

Tested smoke co2 one passed one failed replacement of failed detector

Arrived for no-cooling demand and found the outdoor contactor heavily burnt/corroded with heat-damaged wiring and connections. Removed the failed contactor, cut back affected conductors to clean copper, and repaired/re-terminated wiring as needed. Installed a new contactor and verified proper line voltage and control operation. Checked compressor startup and initially found excessive inrush current. Installed a compressor saver/hard-start kit to assist compressor startup and reduce electrical stress. After installation, compressor inrush was reduced to approximately 67.4 amps and equipment started normally. Allowed system to operate and verified compressor and condenser fan operation. Electrical components are now secure and equipment is operating and cooling at this time

After Diagnostic found system 2 pounds low on Freon system is now cooling properly at this time for office to collect payment

After Diagnostic on second home condenser last 4 9132 had a faulty capacitor replaced capacitor unit is up and cooling properly at this time seen system is past life expectancy sent estimate for replacement

Upon arrival, client stated system is working properly, but wants to get increased airflow and two back bedroom units. Took videos of attic ductwork will get with management team to help send a proper estimate via email to get increased airflow into the two back bedrooms. Client left house before able to get payment. Need to get payment from client still.

Arrived at customer’s home to cut in 7 can lights in living room and kitchen, and to replace the dimmer for dining chandelier. Upon arrival I found that customer purchased can lights themselves. Dropped price of estimate to reflect this as customer preferred to use their fixtures. Cut in can lights in kitchen off of existing light fixture in center of kitchen. Cut in can lights in living room off of existing fan light kit. Landed all connections and confirmed proper operation of fixtures with customer. Replaced dimmer in kitchen for dining room chandelier and confirmed proper operation of all fixtures/switches with customer to complete scope of work for today.

🛠️ Demand Service – No Cool 🔍 Diagnosis * Client reported system was not maintaining temperature. * Indoor blower was operating. * Found condenser fan motor running, but compressor was not initially operating. * Diagnosed a stuck contactor, causing improper compressor operation. * Compressor could continue running without the condenser fan, causing overheating and repeated shutdowns. 🗣️ Client Communication * Explained findings and recommended contactor replacement. * Replaced contactor and verified system operation. ✅ Resolution * System is now cycling properly. * Compressor and condenser fan are operating together. * System is operating properly and within limits.

Fau attic access is in main lobby. Found water spilling from safety pan, primary line is clogged. Vacuumed all water out from the pan. Cleared condensation line from jones valve. Termination point for primary line ties into sink in exam room 5. System is draining properly and cooling at this time of service.

Arrived at customer’s home to diagnose fixture flickering and to give a price for cutting in 7 cans. Found that dimmer for chandelier is old and is most likely the cause of the flickering. Gave customer a price for cutting cans in and replacing the dimmer for the chandelier. Customer also stated that they’d like an outlet replaced on the exterior of home. Replaced outlet for customer and customer signed estimate for work to complete my scope of work for today.

Performed annual preventative maintenance on the system. * Replaced two (2) 20” × 30” air filters (upstairs). * Checked operation of both Honeywell T6 thermostats (one downstairs and one upstairs). * Verified proper sequence of operation. * Checked refrigerant charge; system operating within normal range. * Measured compressor amperage: * Running amperage: Within manufacturer specifications * Startup (inrush) amperage: Approximately 7 amps above normal specifications. * Tested dual run capacitor: * Rated: 40/10 µF, 440V * Measured: 40/10 µF (within specification). * Thoroughly cleaned the outdoor condenser coil. * Cleared debris from around the outdoor unit to improve airflow. The system is operating properly at this time. All inspected components are functioning within normal operating parameters.

Emailed estimate per request.

Performed a cooling maintenance on 2 Lennox condenser, condenser located on right side of home, filter through house ceiling , fau located in attic, changed 2 20x30 filter , flushed condensation line, checked for thermostat on condenser check for amperage and voltage, check for compressor, check for freon level, check for capacitors, check for disconnect box everything within range also clear out dust accumulated inside electrical component area and rinsed condenser coil. Systems are working within specification in cooling at the time of maintenance.

Performed a cooling maintenance on a carrier condenser, condenser located on backside of home, filter located in hallway ceiling, fau located in attic, changed 20x30 filter, flushed condensation line, on condenser check for amperage and voltage, check for compressor, check for freon level, check for capacitors, everything within range also clear out dust accumulated inside electrical component area and rinsed condenser coil. System is working within specification in cooling at the time of maintenance.

Installing 5 Ton American Standard Gold 17 horizontal Split Heat Pump System.

Dropped off other portable