Indio, CA

Completed a heating maintenance on two gas furnace systems. Inspected both systems and verified proper operation in heating mode. Checked thermostat controls and confirmed proper sequence of operations to ensure both furnaces are operating as intended. Inspected blower motors, checked all electrical components and connections, and verified temperature rise on both systems to ensure everything is operating within manufacturer specifications. Cleaned out both condensation drain lines to ensure proper drainage and prevent potential blockages. Checked and inspected filters and replaced them as needed. Also verified proper system operation and made sure both systems switched back into cooling mode correctly after completing the heating maintenance. At this time, both gas furnace systems are operating properly, with all inspected components and readings within manufacturer specifications. No further recommendations at this time.

🔥💨 Single system service 2019 American standard split system Furnace is located in attic / master closet access Condenser located on ground Semi annual HVAC fall service Replaced 14 x 14 and 16 x 30 filters/ceiling mounted. Cycle equipment followed heating sequence of operation, checked, inducer fan motor, blower motor, flame sensor, gas, pressure, heating safety sensors, amps and voltage Cleared condensation line, cleaned out burners, furnace, and mechanical platform Thermostat checked out OK. Ducting is properly secure and strapped to equipment ✅ System checked out operational at this visit 📆 Client will call office to schedule summer visit

Installed 3 ton evaporated coil in attic

Completed a heating maintenance on one split-system heat pump located in the attic access. Began by inspecting the indoor unit and checking thermostat operation, thermostat controls, and the overall sequence of operations to ensure the system was operating properly in heating mode. Checked the electrical components, blower motor operation, and temperature rise to verify everything was operating within manufacturer specifications. Cleaned out the condensation drain line and replaced the air filter. After completing the indoor heating maintenance, I switched the system over to cooling mode and inspected the outdoor heat pump unit. Checked the outdoor electrical components, including compressor amperage, condenser fan motor amperage, capacitors, contactor, and high-voltage and low-voltage wiring. Also inspected the refrigerant performance and overall condition of the outdoor unit. All electrical readings and system operations were within manufacturer specifications at this time. After co

I Performed Maintenance on both the Heating Systems. Also replaced 2) 20x20 filters and flushed both the condensate drain from the attic. Both Heating Systems are 2022 Heat Pump model and over 20 years old York furnace located in the attic and outside on the ground. Verifed proper heating sequence of operation on both systems. At the time of today’s maintenance visit both systems checked out operational. Scheduled next Maintenance visit online.

Arrived on location found none of the new circuit plugs working check GFI‘s would not reset went out to panel. Check the panel through a couple breakers to make sure they were not sticking and we’re hot. Came back in after further examination GFI near water heater bad going to replace.

Installed 2 ton ductless in garage

On arrival found thermostat set for 90° inside temperature 81— no indoor fan running Walked Client through system mode, settings reference auto— cool— Heat—-off—— set 1050 cool equals 88—-Heat equals 65—— permanent hold on —— fan set to auto —— Client needed some thermostat education—— verified that Phone app works= yes

Indoor unit safety inspection and maintenance. Equipment executed the sequence of operation in heating with no carbon monoxide detected in the home. Surge protection: active. Indoor air quality: active. ECM blower motor. Checked blower motor amp draw, static pressure measurements and temperature heat rise. Thermostat: good. System is functioning according to manufacture specifications.

Performed annual heating maintenance on a 2021 Goodman split system. Replaced 20x36, 14x14, 20x20, and 2) 12x12 filters. Fau attic access is located in master closet. Cleaned out burners furnace. Verified heating sequence of operation is working properly according to manufacturer specifications. Checked and detected zero carbon monoxide. Checked temperature rise. Cleared condensation line from fau. Informed and recommended whole home surge protection to client. Sent estimates via email. Client to call office if she has any more questions. Zoning checked out operational. Thermostat checked out operational. System is working properly in heating at this time of service.