Coachella, CA

After Diagnostic found faulty contactor replaced contactor unit is cooling properly advised client leave system off for two hours and fan running system was iced up

Arrived to remove and replace two GFCI outlets on the exterior of the barn. Additionally customer wanted to have all the outlets in the barn to be inspected to ensure they are working. After testing all the outlets I found two that were faulty and I replaced them. All outlets are now working properly.

Performed an indoor safety maintenance on  Armstrong furnaces. Filters located inside filter rack, fau located in hallway closet, changed 16x25 filter, flushed condensation line, on fau followed sequence of operation, checked for amperage and voltage, checked for blower speed, check for any loose connections, check for carbon monoxide, check for temperature rise, check for capacitor, everything within range also cleared dust accumulated inside electrical component. Systems are working within specifications in heating at the time of maintenance. Gave Starbucks gift card

🔥💨❄️ 2021 American Standard split heat/POV Gold 17 Air handler located in attic Condenser located on ground Semi annual HVAC fall service Replaced 20 x 30 and 12 x 12 ceiling mounted filters Cycled equipment followed system sequence of operation Air handler cleared condensation line, checked blower motor amps Verified ducting is properly strapped to equipment and sealed Cleaned off air handler, and mechanical platform UV light checked out OK Check for any moving or vibrating parts in attic/ nothing was found Condenser checked, capacitor, fan motor, compressor, amps and voltage Verified reversing valve operation Ecobee thermostat checked out OK ✅ System checked out operational at this visit 🎃☕️ Gave Client Starbucks gift card for October maintenance

Arrived at customer’s home to diagnose fan control not getting power. Upon arrival I traced switchleg wire for fan to the outlet behind electric fireplace. This discovery led me back to the switch box in question, as there was a white wire that was capped in the box. Traced this wire to outlet behind fireplace and determined that switchleg went through this box, and the maintenance guy that tried to replace fan mixed up the wires based on color code. Rearranged wires to make white wire the proper switchleg for fan to restore power to fan and resolve issue. When tested the fan we noticed an audible rattle inside fan. Informed customer of this and they said they would have the maintenance guy take a look at it.

Performed an indoor safety maintenance American standard furnaces. Filters located in ceiling, fau located in attic, attic access located in hallway, change 20x30 filter, flushed condensation line, on fau followed sequence of operation, checked for amperage and voltage, checked for blower speed, check for any loose connections, check for temperature rise, everything within range also cleared dust accumulated inside electrical component. System is working within specifications in heating at the time of maintenance. Gave Starbucks gift card

We will need to return to continue tracing ceiling fan circuit.

Upon arrival compressor and blower motor was running after Diagnostic found a seized condenser fan motor replaced motor under warranty unit is up and cooling

🛠️🛠️ Upon arrival Client informed me that system wasn’t cooling and outdoor condenser fan motor isn’t spinning Checked capacitor, installed test capacitor and it was determined that fan motor was ceased Spoke with homeowner and informed him of findings Client approved necessary repairs and signed up on membership Replaced condenser fan motor, capacitor. ❄️🧊 pre-performed summer maintenance, checked refrigerant pressures, compressor and fan motor amps. Went up to attic and cleared condensation, and inspected attic Thermostat checked out ok replaced 20x30 filter and rinsed condenser coil ✅ System is now cooling properly. 🎃☕️ Left Starbucks gift card at front door for October maintenance

Installed 3 Ton American Standard Gold 17 Horizontal Split Heat Pump.

Performed a cool maintenance on a newly installed package unit. Check sequence of operation by checking out all electrical and also checked refrigeration levels by performing a temperature split. At this time was getting a 20° split and all electrical components are within range check blower motor, which is very clean. Also wash down package unit and finish maintenance by making sure your system went into heat mode correctly. All is within the range.

Provided estimate to replace 6 motion sensor.

On show called both numbers on file office called clients as well and no response. Waited 15 outside of house no response.

Performed annual safety check in cooling on a York package unit followed Sequence of operation Changed 20x25 filter location hallway checked amps on compressor and condenser fan motor capacitors temperature split working at range cleared condensation line rinsed condenser coil down unit is working to manufacture specification in cooling

Upon arrival system is on a running client stated there was a trip breaker and switch breaker on checked RLA on compressor are high max amps 14.7 system is running at 17 which is tripping breaker due to age of system. We will be installing 17 seer Monday the 28th. From 8 to 10.

Arrived to troubleshoot no power to part of the kitchen. During inspection of panel I discovered I tripped 2 pole breaker. After resetting breaker power was restored to kitchen. Additionally I inspected a motion sensor in closet that was not functioning correctly. After inspection of motion sensor I can confirm the sensor is malfunctioning. Customer would like an estimate to replace 5 motion sensors for 5 closets.

Performed an indoor maintenance and safety inspection. Gas furnace is located in an outdoor mechanical closet. Checked electric motors. Static pressure: N/A. Equipment executed the sequence of operation in heating. Temperature heat rise. Perform service on garage mini split. HVAC duct inspection. System is currently functioning according to manufacture specifications. Pre-booked heating maintenance.

Sent estimate for replacement for duck work there’s no access to replace we will need to cut drywall

After Diagnostic found faulty capacitor replaced capacitor unit is up and cooling performed temperature split and pressures system has Freon temperature split 15 degrees system is cooling but not properly unit is r 22 no longer manufactured sent estimates for replacement system is past life expectancy also signed up client on comfort plan

Tested smoke co2 one passed one failed replacement of failed detector

Arrived for no-cooling demand and found the outdoor contactor heavily burnt/corroded with heat-damaged wiring and connections. Removed the failed contactor, cut back affected conductors to clean copper, and repaired/re-terminated wiring as needed. Installed a new contactor and verified proper line voltage and control operation. Checked compressor startup and initially found excessive inrush current. Installed a compressor saver/hard-start kit to assist compressor startup and reduce electrical stress. After installation, compressor inrush was reduced to approximately 67.4 amps and equipment started normally. Allowed system to operate and verified compressor and condenser fan operation. Electrical components are now secure and equipment is operating and cooling at this time

After Diagnostic found system 2 pounds low on Freon system is now cooling properly at this time for office to collect payment

After Diagnostic on second home condenser last 4 9132 had a faulty capacitor replaced capacitor unit is up and cooling properly at this time seen system is past life expectancy sent estimate for replacement

Upon arrival, client stated system is working properly, but wants to get increased airflow and two back bedroom units. Took videos of attic ductwork will get with management team to help send a proper estimate via email to get increased airflow into the two back bedrooms. Client left house before able to get payment. Need to get payment from client still.

Arrived at customer’s home to cut in 7 can lights in living room and kitchen, and to replace the dimmer for dining chandelier. Upon arrival I found that customer purchased can lights themselves. Dropped price of estimate to reflect this as customer preferred to use their fixtures. Cut in can lights in kitchen off of existing light fixture in center of kitchen. Cut in can lights in living room off of existing fan light kit. Landed all connections and confirmed proper operation of fixtures with customer. Replaced dimmer in kitchen for dining room chandelier and confirmed proper operation of all fixtures/switches with customer to complete scope of work for today.